|
| ISO Grade/AGMA Grade | |||
| Typical Properties* | 100 | 150*** | 220 | 320 |
| AGMA Grade | 3 | 4 | 5 | 6 |
| Viscosity cSt @ 40°C cSt @ 100°C SSU @ 100°C SSU @ 210°C |
100 12.6 518 70 |
150 16.1 783 84 |
220 21.5 1153 108 |
320 27.0 1685 139 |
| Viscosity Index | 120 | 112 | 117 | 112 |
| Specific Gravity @ 60°F | 0.863 | 0.869 | 0.874 | 0.880 |
| Lbs./Gal | 7.19 | 7.24 | 7.28 | 7.33 |
| Flash °F | 440 | 485 | 485 | 500 |
| Pour Point °F | -53 | -47 | -35 | -35 |
| ISO Cleanliness Level | NA | NA | NA | NA |
| ASTM D-1401 Demulsibility (from 40/40/0/06 to 40/40/0/30) |
Pass |
Pass |
Pass |
Pass |
| D-892 Foam Tests Sequences I, II & III | — | — | — | — |
| D-130 Copper Corrosion 3 hrs. @ 210°F 250 hrs. @ 210°F |
1A 1A |
1A 1A |
1A 1A |
1A 1A |
| Cincinnati Millicron “A" 72 hrs. @ 275°F |
Pass |
Pass |
Pass |
Pass |
| D-665 Rust Test Fresh Water Salt Water |
Pass Pass |
Pass Pass |
Pass Pass |
Pass Pass |
| D-2893 Dry Air Oxidation 312 hrs. @ 203°F, % Viscosity Increase Precip. No. (% Solids) |
0 0 |
0 0 |
0 0 |
0 0 |
*All properties are typical and may vary.
Note:
ROOTS Synthetic Oil’s solvency cleans wear metals and deposits left behind by previous oils. These wear metals and deposits can become soluble in the new oil, causing abnormally high values on used oil analysis until equipment is clean.
Note:
ROOTS Synthetic Oil is NSF approved for ISO-VG 32, 150, 220 and 320.
Specified lubricants
| 2"-8" Blower Recommended Oil Grades | |
| Ambient Temperature | ISO Viscosity Range |
| Above 90°F (32°C) | 320 |
| 32° to 90°F (0°-32°C) | 220 |
| 0° to 32°F (-18°-0°C) | 150 |
| Below 0°F (-18°C) | 100 |
| 10"-20" Splash Lubricated Blower Recommended Lubricating Oils | |
| Ambient Temperature | ISO Viscosity Range |
| Above 90°F (32°C) | 320 |
| 32° to 90°F (0°-32°C) | 220 |
| 0° to 32°F (-18°-0°C) | 150 |
| Below 0°F (-18°C) | 100 |
| 10"-20" Pressure Lubricated Blower Recommended Lubricating Oils | |
| Ambient Temperature | ISO Viscosity Range |
| 32° to 120°F (0°-49°C) | 220 |
| Below 32°F (0°C) | 100 |
All RGS - Use ISO-VG-100
See the manual provided with the blower for service intervals of the lubrications mentioned.
所有評論僅代表網友意見，與本站立場無關。